User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: Acromag 1800-K-TC:Signal Conditioner DATE: 26-Jun-96 AUTHOR: User Contributed REVISION: H ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 57 NUMBER OF LINES: 1238 STANDARD: HP 34401A-1 STANDARD: HP 34401A STANDARD: Ectron 1120-1 STANDARD: Ectron 1120 ============================================================================= STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON # Equipment #Various Type:Acromag Signal Conditioner Racks. # Notes:This procedure covers both Dyno and Portable Acromag racks. # Revision Notes: Rev F; Complete rewrite. Changed power supply tolerance to # ñ10% (MFR SPEC) and added provisions for portable cal Rack. REV G; Added # steps to skip the last 8 channels to allow for cal of J dyno lower rack. # REV H; Added STD fsc option for multiple DMM (701-138) and ECTRON (701-139). # and changed IEEE fsc to channel address instead of alias name. # # # Review Approval:_____________________________ Release Date:____/___/____ 1.001 ASK+ M X 1.002 ASK- R N P F W 1.003 RSLT =Accuracy: Signal Conditioner Card OUTPUT; 1.004 RSLT = 0-5VDC ñ0.2% Full Scale 1.005 RSLT = Power Supplies +15 and -15VDC; 1.006 RSLT = ñ10% 1.007 RSLT =Reference Documents:Manufacturers Manual 1.008 RSLT = 1.009 HEAD Setup 1.010 DISP Allow the Ectron and DMM sufficient time to warm up 1.010 DISP prior to continuing. Open the Acromag enclosure and 1.010 DISP allow the internal cabinet temperature to stabilize. 1.011 OPBR Are you using DMM Number 701-001? 1.012 JMPT 1.015 1.013 STD HP 34401A-1 1.014 JMP 1.016 1.015 STD HP 34401A 1.016 OPBR Are you using Ectron Number 701-064? 1.017 JMPT 1.020 1.018 STD Ectron 1120-1 1.019 JMP 1.021 1.020 STD Ectron 1120 1.021 HEAD {UUT Power Supplies} 1.022 DISP The UUT must have its full complement of signal cond- 1.022 DISP itioner cards installed before measuring the supply 1.022 DISP voltages. 1.023 OPBR Do you need to measure the UUT supply voltages? 1.024 JMPF 3.002 # Automatic (IEEE) UUT Supply voltage Entry 1.025 HEAD +15VDC UUT Supply OUTPUT 1.026 DISP Connect the DMM to the UUT +15VDC supply output. 1.026 DISP 1.026 DISP Hit ADVANCE when ready to take readings. 1.027 IEEE [@28]*rst 1.027 IEEE [@28]*cls 1.028 IEEE [@28]conf:volt:dc 100,min 1.029 IEEE [@28]trig:sour imm 1.030 IEEE [@28]trig:del 2 1.031 IEEE [@28]read? 1.032 IEEE [@28][I] 1.033 ACC 100 15.000VDC 3.5e-3% 6e-4/ 1.034 MEME 1.035 MEMC VDC 10% 2.001 HEAD UUT -15VDC Supply OUTPUT 2.002 DISP Connect the DMM to the UUT -15VDC supply output. 2.002 DISP 2.002 DISP Hit ADVANCE when ready to take readings. 2.003 IEEE [@28]read? 2.004 IEEE [@28][I] 2.005 ACC 100 -15.000VDC 3.5e-3% 6e-4/ 2.006 MEME 2.007 MEMC VDC 10% 3.001 JMP 5.001 #Manual UUT Supply Voltage Entry 3.002 HEAD Manual Entry +15VDC UUT Supply 3.003 DISP You must have measured the UUT supply voltages, 3.003 DISP using the HP34401A, during THIS calibration to 3.003 DISP enter the values next. 3.004 ACC 100 15.000VDC 3.5e-3% 6e-4/ 3.005 MEMI Enter the +15VDC UUT supply value (3 places ONLY). 3.006 MEME 3.007 MEMC VDC 10% 4.001 HEAD Manual Entry -15VDC UUT Supply 4.002 ACC 100 -15.000VDC 3.5e-3% 6e-4/ 4.003 MEMI Enter the -15VDC UUT supply value (3 places ONLY). 4.004 MEME 4.005 MEMC VDC 10% #Portable Calibration Supply 5.001 OPBR Are you using the Portable Calibration Rack? 5.002 MATH m[1]=mem1 5.003 JMPF 9.005 5.004 HEAD {Portable Calibration Rack Power Supplies} 5.005 DISP Transfer all of the UUT signal conditioner cards from 5.005 DISP the UUT rack to the portable rack. 5.005 DISP 5.005 DISP BE SURE POWER TO BOTH UUT AND PORTABLE RACKS IS OFF 5.005 DISP BEFORE REMOVING AND INSERTING CARDS!!!!!!!!!!!!!!!! 5.006 DISP If necessary, allow cards a few minutes to warm 5.006 DISP up before continuing. 5.007 OPBR Do you need to measure the Portable Rack supplies? 5.008 JMPF 7.002 #Automatic (IEEE) Portable Rack supply readings. 5.009 HEAD Portable Rack +15VDC supply 5.010 DISP Connect the DMM to the Portable Rack +15VDC OUTPUT. 5.010 DISP 5.010 DISP Hit ADVANCE when ready to take readings. 5.011 IEEE [@28]read? 5.012 IEEE [@28][I] 5.013 ACC 100 15.000VDC 3.5e-3% 6e-4/ 5.014 MEME 5.015 MEMC VDC 10% 6.001 HEAD Portable Rack -15VDC supply 6.002 DISP Connect the DMM to the Portable Rack -15VDC OUTPUT. 6.002 DISP 6.002 DISP Hit ADVANCE when ready to take readings. 6.003 IEEE [@28]read? 6.004 IEEE [@28][I] 6.005 ACC 100 -15.000VDC 3.5e-3% 6e-4/ 6.006 MEME 6.007 MEMC VDC 10% 7.001 JMP 9.001 # Manual Portable Rack Supply Entry. 7.002 HEAD Manual Entry +15VDC Portable Rack Supply 7.003 MATH mem1=0 7.004 DISP You must have measured the Portable Rack's supply 7.004 DISP voltage, using the HP34401A, during THIS calibration 7.004 DISP to enter the values next. 7.005 ACC 100 15.000VDC 3.5e-3% 6e-4/ 7.006 MEMI Enter the +15VDC UUT supply value (3 places ONLY). 7.007 MEME 7.008 MEMC VDC 10% 8.001 HEAD Manual Entry -15VDC Portable Rack Supply 8.002 ACC 100 -15.000VDC 3.5e-3% 6e-4/ 8.003 MEMI Enter the -15VDC UUT supply value (3 places ONLY). 8.004 MEME 8.005 MEMC VDC 10% # Test setup connections. 9.001 HEAD Test Setup 9.002 DISP Make the following connections between the Ectron, DMM 9.002 DISP and the Portable Calibration Rack front panel: 9.002 DISP 9.002 DISP Connect the HP34401A to the DMM BNC connector 9.002 DISP Connect the Ectron to the Type K input connector. 9.003 IEEE [@28]conf:volt:dc 10,min 9.004 IEEE [@28]trig:del 5 # Begin Signal Conditioner tests. 9.005 RSLT =Signal Conditioner Output Voltages checked at ZERO, 9.006 RSLT =1200 and 2400 degrees F input. 9.007 RSLT = 9.008 HEAD {Card 0/Channel 1} 9.009 MATH mem1=m[1] #jump to portable connections. 9.010 JMPT 9.013 #Manual conn. instructions 9.011 DISP Connect the HP34401A to the output of Card 0. 9.011 DISP Connect the Ectron to Input Channel 1. 9.011 DISP 9.011 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 9.012 JMP 9.014 #Portable conn. instructions 9.013 DISP Select Channel 1 on BOTH T/C input and VDC output 9.013 DISP front panel selectors. # Ectron setup DMM read. 9.014 HEAD Channel 1 @ ZERO Degrees 9.015 IEEE [@8]WWWWWWW 9.016 IEEE [@8]AKF0Z 9.017 IEEE [@28]read? 9.018 IEEE [@28][I] 9.019 ACC 10 0.000VDC 2e-3% 5e-4/ 9.020 MEME 9.021 MEMC ÿVDC 0.010U 10.001 HEAD Channel 1 @ 1200 Degrees 10.002 IEEE [@8]WWWWWWW 10.003 IEEE [@8]AKF1200Z 10.004 IEEE [@28]read? 10.005 IEEE [@28][I] 10.006 ACC 10 2.579VDC 2e-3% 5e-4/ 10.007 MEME 10.008 MEMC ÿVDC 0.010U 11.001 HEAD Channel 1 @ 2400 Degrees 11.002 IEEE [@8]WWWWWWW 11.003 IEEE [@8]AKF2400Z 11.004 IEEE [@28]read? 11.005 IEEE [@28][I] 11.006 ACC 10 5.000VDC 2e-3% 5e-4/ 11.007 MEME 11.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 12.001 OPBR Do you NEED to make adjustments? 12.001 OPBR 12.001 OPBR Your results MUST have been greater than 70% of 12.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 12.002 JMPF 12.016 12.003 IEEE [@28]conf:volt:dc 10,.00001 12.004 IEEE [@28][gtl] 12.005 HEAD ZERO Check/Adjustment 12.006 IEEE [@8]wwwwwww 12.007 IEEE [@8]AKF0Z 12.008 DISP When DMM reading stabilizes, adjust Card "Z" to 12.008 DISP obtain 0.000 Volts output. 12.008 DISP 12.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 12.009 HEAD SPAN Check/Adjustment 12.010 IEEE [@8]AKF2400Z 12.011 DISP When DMM reading stabilizes, adjust Card "S" to 12.011 DISP obtain 5.000 Volts output. 12.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 12.013 JMPT 12.005 12.014 IEEE [@28]conf:volt:dc 10,min 12.015 IEEE [@28]trig:del 5 12.016 HEAD {Card 1/Channel 2} 12.017 MATH mem1=m[1] #jump to portable instuctions 12.018 JMPT 12.021 #Manual conn. instructions 12.019 DISP Connect the HP34401A to the output of Card 1. 12.019 DISP Connect the Ectron to Input Channel 2. 12.019 DISP 12.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 12.020 JMP 12.022 #Portable conn. instructions 12.021 DISP Select Channel 2 on BOTH T/C input and VDC output 12.021 DISP front panel selectors. # Ectron setup DMM read. 12.022 HEAD Channel 2 @ ZERO Degrees 12.023 IEEE [@8]WWWWWWW 12.024 IEEE [@8]AKF0Z 12.025 IEEE [@28]read? 12.026 IEEE [@28][I] 12.027 ACC 10 0.000VDC 2e-3% 5e-4/ 12.028 MEME 12.029 MEMC ÿVDC 0.010U 13.001 HEAD Channel 2 @ 1200 Degrees 13.002 IEEE [@8]WWWWWWW 13.003 IEEE [@8]AKF1200Z 13.004 IEEE [@28]read? 13.005 IEEE [@28][I] 13.006 ACC 10 2.579VDC 2e-3% 5e-4/ 13.007 MEME 13.008 MEMC ÿVDC 0.010U 14.001 HEAD Channel 2 @ 2400 Degrees 14.002 IEEE [@8]WWWWWWW 14.003 IEEE [@8]AKF2400Z 14.004 IEEE [@28]read? 14.005 IEEE [@28][I] 14.006 ACC 10 5.000VDC 2e-3% 5e-4/ 14.007 MEME 14.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 15.001 OPBR Do you NEED to make adjustments? 15.001 OPBR 15.001 OPBR Your results MUST have been greater than 70% of 15.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 15.002 JMPF 15.016 15.003 IEEE [@28]conf:volt:dc 10,.00001 15.004 IEEE [@28][gtl] 15.005 HEAD ZERO Check/Adjustment 15.006 IEEE [@8]wwwwwww 15.007 IEEE [@8]AKF0Z 15.008 DISP When DMM reading stabilizes, adjust Card "Z" to 15.008 DISP obtain 0.000 Volts output. 15.008 DISP 15.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 15.009 HEAD SPAN Check/Adjustment 15.010 IEEE [@8]AKF2400Z 15.011 DISP When DMM reading stabilizes, adjust Card "S" to 15.011 DISP obtain 5.000 Volts output. 15.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 15.013 JMPT 15.005 15.014 IEEE [@28]conf:volt:dc 10,min 15.015 IEEE [@28]trig:del 5 15.016 HEAD {Card 2/Channel 3} 15.017 MATH mem1=m[1] #jump to portable instuctions 15.018 JMPT 15.021 #Manual conn. instructions 15.019 DISP Connect the HP34401A to the output of Card 2. 15.019 DISP Connect the Ectron to Input Channel 3. 15.019 DISP 15.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 15.020 JMP 15.022 #Portable conn. instructions 15.021 DISP Select Channel 3 on BOTH T/C input and VDC output 15.021 DISP front panel selectors. # Ectron setup DMM read. 15.022 HEAD Channel 3 @ ZERO Degrees 15.023 IEEE [@8]WWWWWWW 15.024 IEEE [@8]AKF0Z 15.025 IEEE [@28]read? 15.026 IEEE [@28][I] 15.027 ACC 10 0.000VDC 2e-3% 5e-4/ 15.028 MEME 15.029 MEMC ÿVDC 0.010U 16.001 HEAD Channel 3 @ 1200 Degrees 16.002 IEEE [@8]WWWWWWW 16.003 IEEE [@8]AKF1200Z 16.004 IEEE [@28]read? 16.005 IEEE [@28][I] 16.006 ACC 10 2.579VDC 2e-3% 5e-4/ 16.007 MEME 16.008 MEMC ÿVDC 0.010U 17.001 HEAD Channel 3 @ 2400 Degrees 17.002 IEEE [@8]WWWWWWW 17.003 IEEE [@8]AKF2400Z 17.004 IEEE [@28]read? 17.005 IEEE [@28][I] 17.006 ACC 10 5.000VDC 2e-3% 5e-4/ 17.007 MEME 17.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 18.001 OPBR Do you NEED to make adjustments? 18.001 OPBR 18.001 OPBR Your results MUST have been greater than 70% of 18.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 18.002 JMPF 18.016 18.003 IEEE [@28]conf:volt:dc 10,.00001 18.004 IEEE [@28][gtl] 18.005 HEAD ZERO Check/Adjustment 18.006 IEEE [@8]wwwwwww 18.007 IEEE [@8]AKF0Z 18.008 DISP When DMM reading stabilizes, adjust Card "Z" to 18.008 DISP obtain 0.000 Volts output. 18.008 DISP 18.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 18.009 HEAD SPAN Check/Adjustment 18.010 IEEE [@8]AKF2400Z 18.011 DISP When DMM reading stabilizes, adjust Card "S" to 18.011 DISP obtain 5.000 Volts output. 18.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 18.013 JMPT 18.005 18.014 IEEE [@28]conf:volt:dc 10,min 18.015 IEEE [@28]trig:del 5 18.016 HEAD {Card 3/Channel 4} 18.017 MATH mem1=m[1] #jump to portable instuctions 18.018 JMPT 18.021 #Manual conn. instructions 18.019 DISP Connect the HP34401A to the output of Card 3. 18.019 DISP Connect the Ectron to Input Channel 4. 18.019 DISP 18.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 18.020 JMP 18.022 #Portable conn. instructions 18.021 DISP Select Channel 4 on BOTH T/C input and VDC output 18.021 DISP front panel selectors. # Ectron setup DMM read. 18.022 HEAD Channel 4 @ ZERO Degrees 18.023 IEEE [@8]WWWWWWW 18.024 IEEE [@8]AKF0Z 18.025 IEEE [@28]read? 18.026 IEEE [@28][I] 18.027 ACC 10 0.000VDC 2e-3% 5e-4/ 18.028 MEME 18.029 MEMC ÿVDC 0.010U 19.001 HEAD Channel 4 @ 1200 Degrees 19.002 IEEE [@8]WWWWWWW 19.003 IEEE [@8]AKF1200Z 19.004 IEEE [@28]read? 19.005 IEEE [@28][I] 19.006 ACC 10 2.579VDC 2e-3% 5e-4/ 19.007 MEME 19.008 MEMC ÿVDC 0.010U 20.001 HEAD Channel 4 @ 2400 Degrees 20.002 IEEE [@8]WWWWWWW 20.003 IEEE [@8]AKF2400Z 20.004 IEEE [@28]read? 20.005 IEEE [@28][I] 20.006 ACC 10 5.000VDC 2e-3% 5e-4/ 20.007 MEME 20.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 21.001 OPBR Do you NEED to make adjustments? 21.001 OPBR 21.001 OPBR Your results MUST have been greater than 70% of 21.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 21.002 JMPF 21.016 21.003 IEEE [@28]conf:volt:dc 10,.00001 21.004 IEEE [@28][gtl] 21.005 HEAD ZERO Check/Adjustment 21.006 IEEE [@8]wwwwwww 21.007 IEEE [@8]AKF0Z 21.008 DISP When DMM reading stabilizes, adjust Card "Z" to 21.008 DISP obtain 0.000 Volts output. 21.008 DISP 21.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 21.009 HEAD SPAN Check/Adjustment 21.010 IEEE [@8]AKF2400Z 21.011 DISP When DMM reading stabilizes, adjust Card "S" to 21.011 DISP obtain 5.000 Volts output. 21.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 21.013 JMPT 21.005 21.014 IEEE [@28]conf:volt:dc 10,min 21.015 IEEE [@28]trig:del 5 21.016 HEAD {Card 4/Channel 5} 21.017 MATH mem1=m[1] #jump to portable instuctions 21.018 JMPT 21.021 #Manual conn. instructions 21.019 DISP Connect the HP34401A to the output of Card 4. 21.019 DISP Connect the Ectron to Input Channel 5. 21.019 DISP 21.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 21.020 JMP 21.022 #Portable conn. instructions 21.021 DISP Select Channel 5 on BOTH T/C input and VDC output 21.021 DISP front panel selectors. # Ectron setup DMM read. 21.022 HEAD Channel 5 @ ZERO Degrees 21.023 IEEE [@8]WWWWWWW 21.024 IEEE [@8]AKF0Z 21.025 IEEE [@28]read? 21.026 IEEE [@28][I] 21.027 ACC 10 0.000VDC 2e-3% 5e-4/ 21.028 MEME 21.029 MEMC ÿVDC 0.010U 22.001 HEAD Channel 5 @ 1200 Degrees 22.002 IEEE [@8]WWWWWWW 22.003 IEEE [@8]AKF1200Z 22.004 IEEE [@28]read? 22.005 IEEE [@28][I] 22.006 ACC 10 2.579VDC 2e-3% 5e-4/ 22.007 MEME 22.008 MEMC ÿVDC 0.010U 23.001 HEAD Channel 5 @ 2400 Degrees 23.002 IEEE [@8]WWWWWWW 23.003 IEEE [@8]AKF2400Z 23.004 IEEE [@28]read? 23.005 IEEE [@28][I] 23.006 ACC 10 5.000VDC 2e-3% 5e-4/ 23.007 MEME 23.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 24.001 OPBR Do you NEED to make adjustments? 24.001 OPBR 24.001 OPBR Your results MUST have been greater than 70% of 24.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 24.002 JMPF 24.016 24.003 IEEE [@28]conf:volt:dc 10,.00001 24.004 IEEE [@28][gtl] 24.005 HEAD ZERO Check/Adjustment 24.006 IEEE [@8]wwwwwww 24.007 IEEE [@8]AKF0Z 24.008 DISP When DMM reading stabilizes, adjust Card "Z" to 24.008 DISP obtain 0.000 Volts output. 24.008 DISP 24.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 24.009 HEAD SPAN Check/Adjustment 24.010 IEEE [@8]AKF2400Z 24.011 DISP When DMM reading stabilizes, adjust Card "S" to 24.011 DISP obtain 5.000 Volts output. 24.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 24.013 JMPT 24.005 24.014 IEEE [@28]conf:volt:dc 10,min 24.015 IEEE [@28]trig:del 5 24.016 HEAD {Card 5/Channel 6} 24.017 MATH mem1=m[1] #jump to portable instuctions 24.018 JMPT 24.021 #Manual conn. instructions 24.019 DISP Connect the HP34401A to the output of Card 5. 24.019 DISP Connect the Ectron to Input Channel 6. 24.019 DISP 24.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 24.020 JMP 24.022 #Portable conn. instructions 24.021 DISP Select Channel 6 on BOTH T/C input and VDC output 24.021 DISP front panel selectors. # Ectron setup DMM read. 24.022 HEAD Channel 6 @ ZERO Degrees 24.023 IEEE [@8]WWWWWWW 24.024 IEEE [@8]AKF0Z 24.025 IEEE [@28]read? 24.026 IEEE [@28][I] 24.027 ACC 10 0.000VDC 2e-3% 5e-4/ 24.028 MEME 24.029 MEMC ÿVDC 0.010U 25.001 HEAD Channel 6 @ 1200 Degrees 25.002 IEEE [@8]WWWWWWW 25.003 IEEE [@8]AKF1200Z 25.004 IEEE [@28]read? 25.005 IEEE [@28][I] 25.006 ACC 10 2.579VDC 2e-3% 5e-4/ 25.007 MEME 25.008 MEMC ÿVDC 0.010U 26.001 HEAD Channel 6 @ 2400 Degrees 26.002 IEEE [@8]WWWWWWW 26.003 IEEE [@8]AKF2400Z 26.004 IEEE [@28]read? 26.005 IEEE [@28][I] 26.006 ACC 10 5.000VDC 2e-3% 5e-4/ 26.007 MEME 26.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 27.001 OPBR Do you NEED to make adjustments? 27.001 OPBR 27.001 OPBR Your results MUST have been greater than 70% of 27.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 27.002 JMPF 27.016 27.003 IEEE [@28]conf:volt:dc 10,.00001 27.004 IEEE [@28][gtl] 27.005 HEAD ZERO Check/Adjustment 27.006 IEEE [@8]wwwwwww 27.007 IEEE [@8]AKF0Z 27.008 DISP When DMM reading stabilizes, adjust Card "Z" to 27.008 DISP obtain 0.000 Volts output. 27.008 DISP 27.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 27.009 HEAD SPAN Check/Adjustment 27.010 IEEE [@8]AKF2400Z 27.011 DISP When DMM reading stabilizes, adjust Card "S" to 27.011 DISP obtain 5.000 Volts output. 27.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 27.013 JMPT 27.005 27.014 IEEE [@28]conf:volt:dc 10,min 27.015 IEEE [@28]trig:del 5 27.016 HEAD {Card 6/Channel 7} 27.017 MATH mem1=m[1] #jump to portable instuctions 27.018 JMPT 27.021 #Manual conn. instructions 27.019 DISP Connect the HP34401A to the output of Card 6. 27.019 DISP Connect the Ectron to Input Channel 7. 27.019 DISP 27.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 27.020 JMP 27.022 #Portable conn. instructions 27.021 DISP Select Channel 7 on BOTH T/C input and VDC output 27.021 DISP front panel selectors. # Ectron setup DMM read. 27.022 HEAD Channel 7 @ ZERO Degrees 27.023 IEEE [@8]WWWWWWW 27.024 IEEE [@8]AKF0Z 27.025 IEEE [@28]read? 27.026 IEEE [@28][I] 27.027 ACC 10 0.000VDC 2e-3% 5e-4/ 27.028 MEME 27.029 MEMC ÿVDC 0.010U 28.001 HEAD Channel 7 @ 1200 Degrees 28.002 IEEE [@8]WWWWWWW 28.003 IEEE [@8]AKF1200Z 28.004 IEEE [@28]read? 28.005 IEEE [@28][I] 28.006 ACC 10 2.579VDC 2e-3% 5e-4/ 28.007 MEME 28.008 MEMC ÿVDC 0.010U 29.001 HEAD Channel 7 @ 2400 Degrees 29.002 IEEE [@8]WWWWWWW 29.003 IEEE [@8]AKF2400Z 29.004 IEEE [@28]read? 29.005 IEEE [@28][I] 29.006 ACC 10 5.000VDC 2e-3% 5e-4/ 29.007 MEME 29.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 30.001 OPBR Do you NEED to make adjustments? 30.001 OPBR 30.001 OPBR Your results MUST have been greater than 70% of 30.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 30.002 JMPF 30.016 30.003 IEEE [@28]conf:volt:dc 10,.00001 30.004 IEEE [@28][gtl] 30.005 HEAD ZERO Check/Adjustment 30.006 IEEE [@8]wwwwwww 30.007 IEEE [@8]AKF0Z 30.008 DISP When DMM reading stabilizes, adjust Card "Z" to 30.008 DISP obtain 0.000 Volts output. 30.008 DISP 30.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 30.009 HEAD SPAN Check/Adjustment 30.010 IEEE [@8]AKF2400Z 30.011 DISP When DMM reading stabilizes, adjust Card "S" to 30.011 DISP obtain 5.000 Volts output. 30.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 30.013 JMPT 30.005 30.014 IEEE [@28]conf:volt:dc 10,min 30.015 IEEE [@28]trig:del 5 30.016 HEAD {Card 7/Channel 8} 30.017 MATH mem1=m[1] #jump to portable instuctions 30.018 JMPT 30.021 #Manual conn. instructions 30.019 DISP Connect the HP34401A to the output of Card 7. 30.019 DISP Connect the Ectron to Input Channel 8. 30.019 DISP 30.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 30.020 JMP 30.022 #Portable conn. instructions 30.021 DISP Select Channel 8 on BOTH T/C input and VDC output 30.021 DISP front panel selectors. # Ectron setup DMM read. 30.022 HEAD Channel 8 @ ZERO Degrees 30.023 IEEE [@8]WWWWWWW 30.024 IEEE [@8]AKF0Z 30.025 IEEE [@28]read? 30.026 IEEE [@28][I] 30.027 ACC 10 0.000VDC 2e-3% 5e-4/ 30.028 MEME 30.029 MEMC ÿVDC 0.010U 31.001 HEAD Channel 8 @ 1200 Degrees 31.002 IEEE [@8]WWWWWWW 31.003 IEEE [@8]AKF1200Z 31.004 IEEE [@28]read? 31.005 IEEE [@28][I] 31.006 ACC 10 2.579VDC 2e-3% 5e-4/ 31.007 MEME 31.008 MEMC ÿVDC 0.010U 32.001 HEAD Channel 8 @ 2400 Degrees 32.002 IEEE [@8]WWWWWWW 32.003 IEEE [@8]AKF2400Z 32.004 IEEE [@28]read? 32.005 IEEE [@28][I] 32.006 ACC 10 5.000VDC 2e-3% 5e-4/ 32.007 MEME 32.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 33.001 OPBR Do you NEED to make adjustments? 33.001 OPBR 33.001 OPBR Your results MUST have been greater than 70% of 33.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 33.002 JMPF 33.016 33.003 IEEE [@28]conf:volt:dc 10,.00001 33.004 IEEE [@28][gtl] 33.005 HEAD ZERO Check/Adjustment 33.006 IEEE [@8]wwwwwww 33.007 IEEE [@8]AKF0Z 33.008 DISP When DMM reading stabilizes, adjust Card "Z" to 33.008 DISP obtain 0.000 Volts output. 33.008 DISP 33.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 33.009 HEAD SPAN Check/Adjustment 33.010 IEEE [@8]AKF2400Z 33.011 DISP When DMM reading stabilizes, adjust Card "S" to 33.011 DISP obtain 5.000 Volts output. 33.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 33.013 JMPT 33.005 33.014 IEEE [@28]conf:volt:dc 10,min 33.015 IEEE [@28]trig:del 5 33.016 DISP If you are calibrating J dynamometer's lower rack 33.016 DISP it probably only has eight cards in it. 33.017 OPBR Is this J Dynamometer's Lower rack? 33.018 JMPT 57.016 33.019 HEAD {Card 8/Channel 9} 33.020 MATH mem1=m[1] #jump to portable instuctions 33.021 JMPT 33.024 #Manual conn. instructions 33.022 DISP Connect the HP34401A to the output of Card 8. 33.022 DISP Connect the Ectron to Input Channel 9. 33.022 DISP 33.022 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 33.023 JMP 33.025 #Portable conn. instructions 33.024 DISP Select Channel 9 on BOTH T/C input and VDC output 33.024 DISP front panel selectors. # Ectron setup DMM read. 33.025 HEAD Channel 9 @ ZERO Degrees 33.026 IEEE [@8]WWWWWWW 33.027 IEEE [@8]AKF0Z 33.028 IEEE [@28]read? 33.029 IEEE [@28][I] 33.030 ACC 10 0.000VDC 2e-3% 5e-4/ 33.031 MEME 33.032 MEMC ÿVDC 0.010U 34.001 HEAD Channel 9 @ 1200 Degrees 34.002 IEEE [@8]WWWWWWW 34.003 IEEE [@8]AKF1200Z 34.004 IEEE [@28]read? 34.005 IEEE [@28][I] 34.006 ACC 10 2.579VDC 2e-3% 5e-4/ 34.007 MEME 34.008 MEMC ÿVDC 0.010U 35.001 HEAD Channel 9 @ 2400 Degrees 35.002 IEEE [@8]WWWWWWW 35.003 IEEE [@8]AKF2400Z 35.004 IEEE [@28]read? 35.005 IEEE [@28][I] 35.006 ACC 10 5.000VDC 2e-3% 5e-4/ 35.007 MEME 35.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 36.001 OPBR Do you NEED to make adjustments? 36.001 OPBR 36.001 OPBR Your results MUST have been greater than 70% of 36.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 36.002 JMPF 36.016 36.003 IEEE [@28]conf:volt:dc 10,.00001 36.004 IEEE [@28][gtl] 36.005 HEAD ZERO Check/Adjustment 36.006 IEEE [@8]wwwwwww 36.007 IEEE [@8]AKF0Z 36.008 DISP When DMM reading stabilizes, adjust Card "Z" to 36.008 DISP obtain 0.000 Volts output. 36.008 DISP 36.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 36.009 HEAD SPAN Check/Adjustment 36.010 IEEE [@8]AKF2400Z 36.011 DISP When DMM reading stabilizes, adjust Card "S" to 36.011 DISP obtain 5.000 Volts output. 36.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 36.013 JMPT 36.005 36.014 IEEE [@28]conf:volt:dc 10,min 36.015 IEEE [@28]trig:del 5 36.016 HEAD {Card 9/Channel 10} 36.017 MATH mem1=m[1] #jump to portable instuctions 36.018 JMPT 36.021 #Manual conn. instructions 36.019 DISP Connect the HP34401A to the output of Card 9. 36.019 DISP Connect the Ectron to Input Channel 10. 36.019 DISP 36.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 36.020 JMP 36.022 #Portable conn. instructions 36.021 DISP Select Channel 10 on BOTH T/C input and VDC output 36.021 DISP front panel selectors. # Ectron setup DMM read. 36.022 HEAD Channel 10 @ ZERO Degrees 36.023 IEEE [@8]WWWWWWW 36.024 IEEE [@8]AKF0Z 36.025 IEEE [@28]read? 36.026 IEEE [@28][I] 36.027 ACC 10 0.000VDC 2e-3% 5e-4/ 36.028 MEME 36.029 MEMC ÿVDC 0.010U 37.001 HEAD Channel 10 @ 1200 Degrees 37.002 IEEE [@8]WWWWWWW 37.003 IEEE [@8]AKF1200Z 37.004 IEEE [@28]read? 37.005 IEEE [@28][I] 37.006 ACC 10 2.579VDC 2e-3% 5e-4/ 37.007 MEME 37.008 MEMC ÿVDC 0.010U 38.001 HEAD Channel 10 @ 2400 Degrees 38.002 IEEE [@8]WWWWWWW 38.003 IEEE [@8]AKF2400Z 38.004 IEEE [@28]read? 38.005 IEEE [@28][I] 38.006 ACC 10 5.000VDC 2e-3% 5e-4/ 38.007 MEME 38.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 39.001 OPBR Do you NEED to make adjustments? 39.001 OPBR 39.001 OPBR Your results MUST have been greater than 70% of 39.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 39.002 JMPF 39.016 39.003 IEEE [@28]conf:volt:dc 10,.00001 39.004 IEEE [@28][gtl] 39.005 HEAD ZERO Check/Adjustment 39.006 IEEE [@8]wwwwwww 39.007 IEEE [@8]AKF0Z 39.008 DISP When DMM reading stabilizes, adjust Card "Z" to 39.008 DISP obtain 0.000 Volts output. 39.008 DISP 39.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 39.009 HEAD SPAN Check/Adjustment 39.010 IEEE [@8]AKF2400Z 39.011 DISP When DMM reading stabilizes, adjust Card "S" to 39.011 DISP obtain 5.000 Volts output. 39.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 39.013 JMPT 39.005 39.014 IEEE [@28]conf:volt:dc 10,min 39.015 IEEE [@28]trig:del 5 39.016 HEAD {Card 10/Channel 11} 39.017 MATH mem1=m[1] #jump to portable instuctions 39.018 JMPT 39.021 #Manual conn. instructions 39.019 DISP Connect the HP34401A to the output of Card 10. 39.019 DISP Connect the Ectron to Input Channel 11. 39.019 DISP 39.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 39.020 JMP 39.022 #Portable conn. instructions 39.021 DISP Select Channel 11 on BOTH T/C input and VDC output 39.021 DISP front panel selectors. # Ectron setup DMM read. 39.022 HEAD Channel 11 @ ZERO Degrees 39.023 IEEE [@8]WWWWWWW 39.024 IEEE [@8]AKF0Z 39.025 IEEE [@28]read? 39.026 IEEE [@28][I] 39.027 ACC 10 0.000VDC 2e-3% 5e-4/ 39.028 MEME 39.029 MEMC ÿVDC 0.010U 40.001 HEAD Channel 11 @ 1200 Degrees 40.002 IEEE [@8]WWWWWWW 40.003 IEEE [@8]AKF1200Z 40.004 IEEE [@28]read? 40.005 IEEE [@28][I] 40.006 ACC 10 2.579VDC 2e-3% 5e-4/ 40.007 MEME 40.008 MEMC ÿVDC 0.010U 41.001 HEAD Channel 11 @ 2400 Degrees 41.002 IEEE [@8]WWWWWWW 41.003 IEEE [@8]AKF2400Z 41.004 IEEE [@28]read? 41.005 IEEE [@28][I] 41.006 ACC 10 5.000VDC 2e-3% 5e-4/ 41.007 MEME 41.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 42.001 OPBR Do you NEED to make adjustments? 42.001 OPBR 42.001 OPBR Your results MUST have been greater than 70% of 42.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 42.002 JMPF 42.016 42.003 IEEE [@28]conf:volt:dc 10,.00001 42.004 IEEE [@28][gtl] 42.005 HEAD ZERO Check/Adjustment 42.006 IEEE [@8]wwwwwww 42.007 IEEE [@8]AKF0Z 42.008 DISP When DMM reading stabilizes, adjust Card "Z" to 42.008 DISP obtain 0.000 Volts output. 42.008 DISP 42.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 42.009 HEAD SPAN Check/Adjustment 42.010 IEEE [@8]AKF2400Z 42.011 DISP When DMM reading stabilizes, adjust Card "S" to 42.011 DISP obtain 5.000 Volts output. 42.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 42.013 JMPT 42.005 42.014 IEEE [@28]conf:volt:dc 10,min 42.015 IEEE [@28]trig:del 5 42.016 HEAD {Card 11/Channel 12} 42.017 MATH mem1=m[1] #jump to portable instuctions 42.018 JMPT 42.021 #Manual conn. instructions 42.019 DISP Connect the HP34401A to the output of Card 11. 42.019 DISP Connect the Ectron to Input Channel 12. 42.019 DISP 42.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 42.020 JMP 42.022 #Portable conn. instructions 42.021 DISP Select Channel 12 on BOTH T/C input and VDC output 42.021 DISP front panel selectors. # Ectron setup DMM read. 42.022 HEAD Channel 12 @ ZERO Degrees 42.023 IEEE [@8]WWWWWWW 42.024 IEEE [@8]AKF0Z 42.025 IEEE [@28]read? 42.026 IEEE [@28][I] 42.027 ACC 10 0.000VDC 2e-3% 5e-4/ 42.028 MEME 42.029 MEMC ÿVDC 0.010U 43.001 HEAD Channel 12 @ 1200 Degrees 43.002 IEEE [@8]WWWWWWW 43.003 IEEE [@8]AKF1200Z 43.004 IEEE [@28]read? 43.005 IEEE [@28][I] 43.006 ACC 10 2.579VDC 2e-3% 5e-4/ 43.007 MEME 43.008 MEMC ÿVDC 0.010U 44.001 HEAD Channel 12 @ 2400 Degrees 44.002 IEEE [@8]WWWWWWW 44.003 IEEE [@8]AKF2400Z 44.004 IEEE [@28]read? 44.005 IEEE [@28][I] 44.006 ACC 10 5.000VDC 2e-3% 5e-4/ 44.007 MEME 44.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 45.001 OPBR Do you NEED to make adjustments? 45.001 OPBR 45.001 OPBR Your results MUST have been greater than 70% of 45.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 45.002 JMPF 45.016 45.003 IEEE [@28]conf:volt:dc 10,.00001 45.004 IEEE [@28][gtl] 45.005 HEAD ZERO Check/Adjustment 45.006 IEEE [@8]wwwwwww 45.007 IEEE [@8]AKF0Z 45.008 DISP When DMM reading stabilizes, adjust Card "Z" to 45.008 DISP obtain 0.000 Volts output. 45.008 DISP 45.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 45.009 HEAD SPAN Check/Adjustment 45.010 IEEE [@8]AKF2400Z 45.011 DISP When DMM reading stabilizes, adjust Card "S" to 45.011 DISP obtain 5.000 Volts output. 45.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 45.013 JMPT 45.005 45.014 IEEE [@28]conf:volt:dc 10,min 45.015 IEEE [@28]trig:del 5 45.016 HEAD {Card 12/Channel 13} 45.017 MATH mem1=m[1] #jump to portable instuctions 45.018 JMPT 45.021 #Manual conn. instructions 45.019 DISP Connect the HP34401A to the output of Card 12. 45.019 DISP Connect the Ectron to Input Channel 13. 45.019 DISP 45.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 45.020 JMP 45.022 #Portable conn. instructions 45.021 DISP Select Channel 13 on BOTH T/C input and VDC output 45.021 DISP front panel selectors. # Ectron setup DMM read. 45.022 HEAD Channel 13 @ ZERO Degrees 45.023 IEEE [@8]WWWWWWW 45.024 IEEE [@8]AKF0Z 45.025 IEEE [@28]read? 45.026 IEEE [@28][I] 45.027 ACC 10 0.000VDC 2e-3% 5e-4/ 45.028 MEME 45.029 MEMC ÿVDC 0.010U 46.001 HEAD Channel 13 @ 1200 Degrees 46.002 IEEE [@8]WWWWWWW 46.003 IEEE [@8]AKF1200Z 46.004 IEEE [@28]read? 46.005 IEEE [@28][I] 46.006 ACC 10 2.579VDC 2e-3% 5e-4/ 46.007 MEME 46.008 MEMC ÿVDC 0.010U 47.001 HEAD Channel 13 @ 2400 Degrees 47.002 IEEE [@8]WWWWWWW 47.003 IEEE [@8]AKF2400Z 47.004 IEEE [@28]read? 47.005 IEEE [@28][I] 47.006 ACC 10 5.000VDC 2e-3% 5e-4/ 47.007 MEME 47.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 48.001 OPBR Do you NEED to make adjustments? 48.001 OPBR 48.001 OPBR Your results MUST have been greater than 70% of 48.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 48.002 JMPF 48.016 48.003 IEEE [@28]conf:volt:dc 10,.00001 48.004 IEEE [@28][gtl] 48.005 HEAD ZERO Check/Adjustment 48.006 IEEE [@8]wwwwwww 48.007 IEEE [@8]AKF0Z 48.008 DISP When DMM reading stabilizes, adjust Card "Z" to 48.008 DISP obtain 0.000 Volts output. 48.008 DISP 48.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 48.009 HEAD SPAN Check/Adjustment 48.010 IEEE [@8]AKF2400Z 48.011 DISP When DMM reading stabilizes, adjust Card "S" to 48.011 DISP obtain 5.000 Volts output. 48.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 48.013 JMPT 48.005 48.014 IEEE [@28]conf:volt:dc 10,min 48.015 IEEE [@28]trig:del 5 48.016 HEAD {Card 13/Channel 14} 48.017 MATH mem1=m[1] #jump to portable instuctions 48.018 JMPT 48.021 #Manual conn. instructions 48.019 DISP Connect the HP34401A to the output of Card 13. 48.019 DISP Connect the Ectron to Input Channel 14. 48.019 DISP 48.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 48.020 JMP 48.022 #Portable conn. instructions 48.021 DISP Select Channel 14 on BOTH T/C input and VDC output 48.021 DISP front panel selectors. # Ectron setup DMM read. 48.022 HEAD Channel 14 @ ZERO Degrees 48.023 IEEE [@8]WWWWWWW 48.024 IEEE [@8]AKF0Z 48.025 IEEE [@28]read? 48.026 IEEE [@28][I] 48.027 ACC 10 0.000VDC 2e-3% 5e-4/ 48.028 MEME 48.029 MEMC ÿVDC 0.010U 49.001 HEAD Channel 14 @ 1200 Degrees 49.002 IEEE [@8]WWWWWWW 49.003 IEEE [@8]AKF1200Z 49.004 IEEE [@28]read? 49.005 IEEE [@28][I] 49.006 ACC 10 2.579VDC 2e-3% 5e-4/ 49.007 MEME 49.008 MEMC ÿVDC 0.010U 50.001 HEAD Channel 14 @ 2400 Degrees 50.002 IEEE [@8]WWWWWWW 50.003 IEEE [@8]AKF2400Z 50.004 IEEE [@28]read? 50.005 IEEE [@28][I] 50.006 ACC 10 5.000VDC 2e-3% 5e-4/ 50.007 MEME 50.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 51.001 OPBR Do you NEED to make adjustments? 51.001 OPBR 51.001 OPBR Your results MUST have been greater than 70% of 51.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 51.002 JMPF 51.016 51.003 IEEE [@28]conf:volt:dc 10,.00001 51.004 IEEE [@28][gtl] 51.005 HEAD ZERO Check/Adjustment 51.006 IEEE [@8]wwwwwww 51.007 IEEE [@8]AKF0Z 51.008 DISP When DMM reading stabilizes, adjust Card "Z" to 51.008 DISP obtain 0.000 Volts output. 51.008 DISP 51.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 51.009 HEAD SPAN Check/Adjustment 51.010 IEEE [@8]AKF2400Z 51.011 DISP When DMM reading stabilizes, adjust Card "S" to 51.011 DISP obtain 5.000 Volts output. 51.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 51.013 JMPT 51.005 51.014 IEEE [@28]conf:volt:dc 10,min 51.015 IEEE [@28]trig:del 5 51.016 HEAD {Card 14/Channel 15} 51.017 MATH mem1=m[1] #jump to portable instuctions 51.018 JMPT 51.021 #Manual conn. instructions 51.019 DISP Connect the HP34401A to the output of Card 14. 51.019 DISP Connect the Ectron to Input Channel 15. 51.019 DISP 51.019 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 51.020 JMP 51.022 #Portable conn. instructions 51.021 DISP Select Channel 15 on BOTH T/C input and VDC output 51.021 DISP front panel selectors. # Ectron setup DMM read. 51.022 HEAD Channel 15 @ ZERO Degrees 51.023 IEEE [@8]WWWWWWW 51.024 IEEE [@8]AKF0Z 51.025 IEEE [@28]read? 51.026 IEEE [@28][I] 51.027 ACC 10 0.000VDC 2e-3% 5e-4/ 51.028 MEME 51.029 MEMC ÿVDC 0.010U 52.001 HEAD Channel 15 @ 1200 Degrees 52.002 IEEE [@8]WWWWWWW 52.003 IEEE [@8]AKF1200Z 52.004 IEEE [@28]read? 52.005 IEEE [@28][I] 52.006 ACC 10 2.579VDC 2e-3% 5e-4/ 52.007 MEME 52.008 MEMC ÿVDC 0.010U 53.001 HEAD Channel 15 @ 2400 Degrees 53.002 IEEE [@8]WWWWWWW 53.003 IEEE [@8]AKF2400Z 53.004 IEEE [@28]read? 53.005 IEEE [@28][I] 53.006 ACC 10 5.000VDC 2e-3% 5e-4/ 53.007 MEME 53.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 54.001 OPBR Do you NEED to make adjustments? 54.001 OPBR 54.001 OPBR Your results MUST have been greater than 70% of 54.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 54.002 JMPF 54.017 54.003 IEEE [@28]conf:volt:dc 10,.00001 54.004 IEEE [@28][gtl] 54.005 HEAD ZERO Check/Adjustment 54.006 IEEE [@8]wwwwwww 54.007 IEEE [@8]AKF0Z 54.008 DISP When DMM reading stabilizes, adjust Card "Z" to 54.008 DISP obtain 0.000 Volts output. 54.008 DISP 54.009 DISP ÿ Hit ADVANCE to Check/Adjust Span. 54.010 HEAD SPAN Check/Adjustment 54.011 IEEE [@8]AKF2400Z 54.012 DISP When DMM reading stabilizes, adjust Card "S" to 54.012 DISP obtain 5.000 Volts output. 54.013 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 54.014 JMPT 54.005 54.015 IEEE [@28]conf:volt:dc 10,min 54.016 IEEE [@28]trig:del 5 54.017 HEAD {Card 15/Channel 16} 54.018 MATH mem1=m[1] #jump to portable instuctions 54.019 JMPT 54.022 #Manual conn. instructions 54.020 DISP Connect the HP34401A to the output of Card 15. 54.020 DISP Connect the Ectron to Input Channel 16. 54.020 DISP 54.020 DISP ÿ Hit ADVANCE to begin measurement sequence. #jump to readings 54.021 JMP 54.023 #Portable conn. instructions 54.022 DISP Select Channel 16 on BOTH T/C input and VDC output 54.022 DISP front panel selectors. # Ectron setup DMM read. 54.023 HEAD Channel 16 @ ZERO Degrees 54.024 IEEE [@8]WWWWWWW 54.025 IEEE [@8]AKF0Z 54.026 IEEE [@28]read? 54.027 IEEE [@28][I] 54.028 ACC 10 0.000VDC 2e-3% 5e-4/ 54.029 MEME 54.030 MEMC ÿVDC 0.010U 55.001 HEAD Channel 16 @ 1200 Degrees 55.002 IEEE [@8]WWWWWWW 55.003 IEEE [@8]AKF1200Z 55.004 IEEE [@28]read? 55.005 IEEE [@28][I] 55.006 ACC 10 2.579VDC 2e-3% 5e-4/ 55.007 MEME 55.008 MEMC ÿVDC 0.010U 56.001 HEAD Channel 16 @ 2400 Degrees 56.002 IEEE [@8]WWWWWWW 56.003 IEEE [@8]AKF2400Z 56.004 IEEE [@28]read? 56.005 IEEE [@28][I] 56.006 ACC 10 5.000VDC 2e-3% 5e-4/ 56.007 MEME 56.008 MEMC VDC 0.010U # Card ADJ: Insert after each channel section 57.001 OPBR Do you NEED to make adjustments? 57.001 OPBR 57.001 OPBR Your results MUST have been greater than 70% of 57.001 OPBR tolerance. # Jump to next channel tests if FALSE (NO). 57.002 JMPF 57.016 57.003 IEEE [@28]conf:volt:dc 10,.00001 57.004 IEEE [@28][gtl] 57.005 HEAD ZERO Check/Adjustment 57.006 IEEE [@8]wwwwwww 57.007 IEEE [@8]AKF0Z 57.008 DISP When DMM reading stabilizes, adjust Card "Z" to 57.008 DISP obtain 0.000 Volts output. 57.008 DISP 57.008 DISP ÿ Hit ADVANCE to Check/Adjust Span. 57.009 HEAD SPAN Check/Adjustment 57.010 IEEE [@8]AKF2400Z 57.011 DISP When DMM reading stabilizes, adjust Card "S" to 57.011 DISP obtain 5.000 Volts output. 57.012 OPBR Do you want to repeat the adjustments? # Jump to ZERO HEAD FSC if TRUE (YES). 57.013 JMPT 57.005 57.014 IEEE [@28]conf:volt:dc 10,min 57.015 IEEE [@28]trig:del 5 57.016 HEAD 57.017 DISP 57.017 DISP ÿ P R O C E D U R E 57.017 DISP ÿ ÿ COMPLETED! 57.017 DISP